J'attends toujours ma commande ont étais à la maison personne n'a sonner le jour la y a un problème ont ma débité les sous mais pas de coli

Fa quello che deve fare ed è economico. Certo non è un prodotto per piastrellisti professionisti ma se si devono tagliare alcune piastrelle per sistemare il terrazzo o la cucina è quello che ci vuole

de helft van de spullen die er bij moeten zitten waren er niet. dus kan ik me klus nog niet afmaken.het lijkt er op dat het pakket onder weg open gemaakt is,

Bon achat, peu coûteux, mais pour une utilisation occasionnelle. Fait le boulot pour un travail sur une surface réduite (2/3m2 ) et pour des carreaux de faïence ou de grès pas trop épais.

Absolute super wet cutter. Duncurin is doing his best to weed and tidy the local church grounds. In addition to the monster weeds, most of the edging stones have, over the many years, been trodden down and shattered. These are Victorian and are made up of fired blue/black clay. I managed to find a small number on an internet auction site but further supplies are expensive and often a long way away.I struck upon the idea of trying to repair as many of the shattered edging stones as I could. The only problem was the rolled top edge which is about 44mm in diameter at its widest point. The actual ‘body’ of the edging stone is thinner about 15 mm. I therefore chose this FERM machine as it will cut to the perpendicular to a depth of 34mm. I was hoping that after my pass through with the cutter then the extra bit on the rolled edge that was not cut through could be sorted with a hacksaw. Unfortunately this is really difficult and the fired clay is impervious to my hacksaw blade. I then had no alternative but to do what I was hoping to avoid – turn the edging stone over and cut from the other side.Well, I must say even for a terrified, weedy chap like me as I cling on to that edging stone – it cuts beautifully and precisely – so precise that even upon turning the edging stone over and cutting from the other side a nice smooth and perpendicular edge is left with no steps or ‘burs’.One or two things help with this. The fence is of aluminium and though not substantial it does hold up quite well as I run the thick edging stone along it and it doesn’t move or buckle. It is also precise and the fence allows me to guide the edging stone through the cutting blade getting a nice clean cut that is perpendicular and clean even when I turn it over and cut again. The motor is fairly quiet and also fairly powerful. As the blade attempts to go through the thickest part ie the rolled top edge then it can get stuck. In this instance I either switch the red switch off pretty smartish or if it is not completely stuck I withdraw the edging stone slowly and as the blade speeds up again I slowly feed it back in.Its important to let the blade take its time – do not try to force or hurry it especially when cutting something this thick.The unit comes with eye and ear protection. I tend to use my own but to be fair the goggles aren’t and though as I have a morbid fear of looking at the blade as it cuts I put my glasses on too as an extra layer of protection.The blade guard is a bit flimsy but actually works well and although water goes everywhere it’s quite easy to avoid the worst of it by using the blade guard and standing to one side a little. I found a polycarbonate visor especially useful as it not only protects your eyes but you can even stop your face from being sprayed as you dare to look at the blade.I also used my own RCD device as there is water everywhere and I am not sure if the big boxy plug as fitted handles this but I thought better to have two than none!Lastly the water reservoir which of course should always be kept at the optimum level is easy to use and most crucially forms a trough which can be removed once finished and then all the crud from the cutting easily cleaned out. The blade protector remains free from debris and crud and does not need removing after use and can be left in situ.I am now planning to take my edging stones with the nice clean perpendicular edges and glue them together with masonry glue and although they will be odd shapes they should be much easier to refit and hopefully form a tidy border.I’m not sure if the Amazon site is accepting pics at present but if it is I will post a couple. In conclusion though an excellent machine ideal for the job I had in mind which it got on without protest and represents excellent value for money !

La compré por que quería cortar azulejos de pasta blanca cerámica,el resultado fue bastante triste,la máquina ofrece cortes descantillados,puede que sea el disco que se incluye,pero lo cierto es que la máquina es endeble y de calidad muy pobre ,con una radial normal y un disco de diamante barato he conseguido mucho mejores resultados1-corte desigual con descantillados2-vibracion extrema.3-salpica una barbaridad.(te quedas sin agua en 2 cortes)la verás toda en el suelo y en tu cara.4-Para que tener un trasto como este si el acabado que deja es horrible y es casi imposible cortar recto con ella.....solo espero algún día... encontrarle algo para lo qu sirva...pérdida de dinero

Calidad precio bien no se puede pedir mas

La hoja que lleva, es de mala calidad y hace corte mal,haciendo que salte la pieza. Por lo demás para trabajos sencillos y que no sea muy importante los remates vale.

Funciona de maravilla para cortar piezas duras de gresite porcelánico . Cortes rectos y de buen rendimiento. refrigerada por agua.

Hace su funcion muy bien, pensaba que iria peor pero me a sorprendido, volberia a comprarlo, lo recomiendo para bricolage

Nos sacó del apuro en una pequeña reforma, hizo los cortes bastante decentes. Calidad precio muy recomendable. Eso sí, importante protegerse bien porq salpica bastante agua con el corte.