２７インチと３２インチのディスプレイの高さの差に丁度はまるwindowspczで使用できますが、タッチはできません。解像度が低いので、設定画面とか全て表示されないので、設定など用にもう一つ画面が必要。

Ein sehr guter Bildschirm über den Preis läst sich streiten aber noch okay. Ich habe ihn für Klipper gebraucht da ich nicht immer den PC anschalten will um die Temperatur zu überwachen und sonst was ich steuern will. Die Installation ging sehr schnell und der KlipperScreen war auch schnell installiert. Das Touchscreen ist sehr gut auch ohne Stift, der mit beigelegt war. Das Display reagiert sehr gut und ohne Verzögerung, also ein gute Investition. Die Größe ist auch sehr gut, voll ausreichend. Ich kann das Display wärmstens empfehlen.

Nice product, wish there is hdmi angled connector.

I've been looking around for a small HDMI LCD screen to use as a seconday screen with Windows and it took a few months of research on and off before deciding on the Elecrow 5" HDMI monitor. For the most part, it took me a while because a lot of reviews here and on other sites were primarily about use and config with Raspberry Pi.Thanks to reviewer Alan who gave a good review with plenty of photos that convinced me to go for it. Not sure if it's just how Amazon stores user review videos but the video review was a bit pixelated so it was hard to appreciate the clarity of the screen but it seemed to be what I was looking for.Having used it for a few months now I still can't believe how clear and sharp the screen is! There are sadly no controls for brightness, colour, saturation or contrast but everything displayed looks very nice and accurate.Usually when you see the resolution 800x480 you think how bad that looks when your PC doesn't have the right drivers installed and it looks blocky. I know it's all relative and about DPI but once I had it all connected and tested it was sharp and clear, almost HD. I wish I had bought one sooner as it is exactly what I was looking for having tried a Lilliput monitor.As I'm using this with Windows, I've not needed to look through the included driver utility disc and not tried the resistive touchscreen so I can't comment on those. Windows just detects it as a second display and lets me extend my desktop. No drivers needed. The box contains the LCD screen, a HDMI bridge connector that neatly connects the HDMI socket on the top of the screen to the HDMI socket on the Raspberry Pi when mounted together. Standoffs for mounting are also supplied plus a plastic stylus.Here are some of the good points that I like:+ It shows the video feed straightaway without any fancy splash screens or slow initialisation pauses. This was one of the annoyances with Lilliput monitor was a slow bright blue screen on power on before it would think about showing the feed. I know it's only a few seconds but I specifically wanted instant feed on power on for future uses.+ Runs off a single micro USB (socket also at the top next to HDMI socket) connected to PC USB so no additional external power adapters or sockets needed. It powers down whenever my PC is scheduled to power down so no lingering standby. Some motherboard USB ports do still continue to supply power for charging devices so your experience may differ.+ I was hoping for an on/off switch but no it only has a backlight switch which I wasn't sure about to begin with but I've since found it very useful and better. I was thinking about buying a micro USB cable designed for Raspberry Pi with an inline power switch built in but for now the brightness switch is fine. As a blessing in disguise, it prevents Windows/DirectShow from blinking all screens when it realises a monitor has been disconnected, that blink would often cause the video on my TV app to freeze. Turning off backlight doesn't cause DirectShow to have a fit.+ Small and light enough that I have it attached to a gooseneck arm so can position it how I need. I was going to buy one of those mobile phone gooseneck arms but I kept reading reviews of some not even being able to cope with weight of a smartphone without drooping so I've used a photographic gooseneck clamp which is a bit overkill but no droop!- The only negative I can think of is the availability or lack of screen cases with cutouts to suit the position of the HDMI and USB sockets on this. The Elecrow has its HDMI and USB socket at the top edge of screen and nearly all cases I have looked at are designed for screens with HDMI and USB on the right edge. I've had to import one from China that had the cutouts for this screen. Took about 2 weeks to arrive. Wish I'd have ordered two cases at the same time to avoid the wait as I'm impressed with the clarity of Elecrow I hope to buy another one in near future.! Just one more thing Columbo! I had originally wanted to buy Revision B of this screen with capacitive touch screen because it has OSD menu buttons. I can't find any manuals but I'm hoping that OSD buttons allows settings for brightness as that was my other preferred criteria. Having said that, I think it would be even more impossible to find suitable case due to the positions of sockets and extra menu buttons on Revision B screen. Maybe Elecrow could provide some insight on available cases?To solve the lack of brightness control I have just used a pieces of tinted acetate so that lessens the brightness if I'm using at night.

Très content de recevoir le produit et m en servir au moment de L alume il me manque deux cm d écran et le tactile ne fonctionne pas je suis dégoûté.