Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Creality Ender 3 V4.2.7 Silent Motherboard with TMC2225 Driver BootLoader for Ender-3 V2/Ender-3 Pro/Ender-5/Ender-5 Pro 3D Printer

Envío gratis en pedidos superiores a 25.99€

82.13€

33 .99 33.99€

En stock

1.Tamaño:Ender3


Acerca de este producto

  • Placa base silenciosa V1.1.5 mejorada de Creality a placa base silenciosa V4.2.7. La madre silenciosa V1.1.5 es de 8 bits, pero la placa base silenciosa V4.2.7 es de 32 bits. Servicio al cliente: Si tienes algún problema al usar esta tabla, no dudes en ponerte en contacto con nosotros a través de Amazon. Te proporcionaremos soluciones.
  • Esta placa base silenciosa adopta controladores TMC2225, que pueden reducir el ruido del motor paso a paso en gran medida.
  • Circuito optimizado: permite la protección térmica contra fugas para resolver eficazmente problemas de calefacción. Se puede utilizar en combinación con el eje de transmisión E/Z/Y/X.
  • Marlin V0.0.6 y Bootloader instalados, el firmware se puede modificar con un cable USB. Ya no necesita un cable ISP ni un tablero ISP.
  • Nota: Tiene el firmware unificado gratuito preconfigurado para Ender-3. Si quieres instalar esta placa en Ender-3 Pro/Ender-5, tendrás que parpadear el firmware. Si no tienes el firmware, ponte en contacto con nosotros



Ignacio
Reseñado en España el 16 de agosto de 2023
Va genial y he aumentado tanto la velocidad de impresión como la tranquilidad. Pero tuve que regular el paso en Z, es superfácil de hacer si tienes un calibre y sabes hacer una regla de tres. El parámetro está en el propio menú de la Ender. Por esto recomiendo imprimir un cubo XYZ por si acaso. (((Si no tienes calibre, imprime el cubo mas grande y usa una simple regla.)))
Slartibartfast
Reseñado en el Reino Unido el 25 de julio de 2023
ok... a lot to explain here but lets start at the beginning.1st one of these that I bought looked like it had been trod on by the delivery driver and worked like it too. The box was crushed on one corner and a couple of the components didn't look to be seated right so after trying it and finding out it was a lemon back it went.I gave up for a while and then had another one bought for my birthday and its a peach. It's a lot quieter on the stepper motors (fans are still noisy) and in my case the print quality is noticeably better without changing anything else.That said, you really need to know the following.I work in IT so had read up on these and knew the standard software that Creality supplies is dire so had already done all the hard work and compiled a custom version of Marlin myself. Unfortunately it was for the 1st broken board which did not get used because the board was broken but it worked straight away on the new one.For the non IT literate this is not that easy a job, yes there are videos and web pages that explain this and if you understand them then you have a chance of doing it. Do remember that Marlin is open source and some of the settings are, shall we say, a bit different. For example, if you have put adjustable belt pulleys on a Ender 3 pro everything is fine with the original board because they set the print area to 220mm, compile Marlin yourself and the config file sets it bigger and it will bang on the Y axis unless you change the settings before compiling.If this sounds like I have just spoken Martian to you or you have taken one look at all the wires on the controller board and screamed... I think you know this is not for you. I am sure that if you know someone who does know what they are doing and you can give them enough beer vouchers then they might fit it for you.IF you think you know what you are doing there are some good sources of info out there and I would suggest you watch out for:- print area size- z probe stop, especially with bl / cr touch- bed levelling method- depending on controller board, chip version and memory size.
Alberto Aguado Robledo
Reseñado en España el 11 de julio de 2023
Es una barbaridad como se ha notado el cambio de placa, es que no se oye nada!Antes tenia que cerrar al puerta por la noche porque se oía muchísimo la impresora. Pero con esto es una pasada
Not a reviewer
Reseñado en Estados Unidos el 4 de junio de 2023
Bought 2 ender 3's and setup my first printer, used it for 2 months while I stockpiled some upgrades for the other while I learned about 3d printing. I thought the sounds it made were super cool and didn't bother me, but the Motors whining bothered my wife. Happy wife happy life, ordered a silent board too. I put together printer #2 (at setup I added dual z kit, direct feed extruder kit, new leveling springs and wheels/knobs, as well as this silent board) and with all my upgrades installed it fired it up and did a quick test print, basically sounded idle, just like when you aren't printing, but the fans are on.This board blew my mind... Well maybe my first machine was just noisier anyway? Nope put a silent board in that one too, super quiet. Now that my printers are quieter, i realized I didn't really like the motor whine after all.My wife? Happy they don't make as much noise now, she didn't even freak out when she saw the second printer (which she didn't know I had for a month lol)Also firmware flash is a snap for 32 bit boards, ignore the complex videos, just drop the binary file from creality website (pick the right one, mine was just the basic cuz no auto level kit) put the binary file on a BLANK SD card, with printer off, insert SD card, power printer on, wait a minute for the blank screen to pass while it updates. Once it boots up, check you printer firmware in the menu and confirm it's what you were expecting. Came preloaded with ender pro firmware from like 2020.Side notes, direct drive kit is cool, I bought it for tpu, nothing special. Dual z kit is cool, critical if adding direct feed extruder, helpful at keeping z from slouching on a bowden, but you don't need it. The knobs and spring kit for bed leveling is my favorite upgrade on the cheap, holds great, I rarely have to re-level, with stock springs I had to re-level pretty much every print. Octoprint/octopi brings it all together so so sweetly, i have raspberry pi on hand most of the time, so I just set it up on a 3b+ as soon as I discovered octoprint. Been running fine, threw another instance of octoprint on a pi400 for the second printer. *If you don't have octoprint setup, that is Upgrade #1, the one upgrade to rule them all. So after octoprint, this silent board is my favorite upgrade, my stock boards were 4.2.2's so no print quality improvement, but the silence is worth gold, quieter fans installed is inevitable now.Worst part about this board, uninstalling the stock board. Creality Hot glued the plugs closed, i hear they recently started doing this, maybe they want to void a warranty, but I'm the kinda guy that if I buy it and it works, it's mine, i fix my own stuff, I was never going to send this machine back, just replace bad parts if there's ever a failure. You do risk breaking something, however I was able to extract 2x4.2.2 boards without damaging them, and even still, you can just use your new board if you damage the stock one, install is pretty easy without glue everywhere, have some tweezers handy to hold wires into terminals while you tighten them in.
Obiquad
Reseñado en Francia el 12 de noviembre de 2023
Installer pour faire évoluer, une ender3 première version, c’est le jour et la nuit, un silence total, extrêmement performante, recommandé fortement pour faire évoluer ses anciennes machines
Jose Ignacio Croce Busquets
Reseñado en España el 5 de enero de 2023
Se me había quemado la controladora original de mi Ender-3 Pro y simplemente buscaba un reemplazo. Pero esta nueva controladora es increiblemente silenciosa y con las ventajas de una controladora de 16bits (no requiere cableado adicional ni parches para actualizar el firmware). Cuenta con conectores adicionales para el detector de fin de filamento (no incluido pero que estoy pensando en incorporar). El reemplazo de la placa por la original fue sencillo y, aunque hay que desmontar mucho, los conectores están claramente identificados y coinciden con los originales.
Joan
Reseñado en España el 21 de enero de 2023
Al poco de utilizarla me saltaba el error de MAXTEMP pero al encender la máquina incuso saltaba con solo la placa en la corriente sin los sensores de temperatura , tenía unos pegotes de pasta térmica de esta por toda la placa como se ve en las fotos fatal y es la 2n que pido que la primera pedí un rembolso pq no encendía
Irok salamander
Reseñado en México el 18 de abril de 2023
Actualice la tarjeta a mi Ender 3, ahora puedo dejar la impresora trabajando en la noche sin preopuarme de que el ruido moleste a mis vecinos. Ahora el ruido mas molesto es el de los ventiladores, pero básicamente es ruido Blanco. La recomiendo, en AliExpress es mas barata, pero igual y no te llega, estoy esperando un sensor de nivelación que compré y que tiene fos semanas de atraso... Si lo hubiera comprado en Amazon ya estaria instalado
alejandro
Reseñado en España el 31 de agosto de 2022
Cumple perfectamente con lo que promete. Mi impresora ya no hace ruidos molestos y, al parecer, innecesarios. Ahora puedo dejarla funcionando de noche en mi habitación ya que hace el mismo ruido que un PC de sobremesa en reposo
Derek Kwasniewski
Reseñado en Estados Unidos el 26 de febrero de 2022
I originally purchased one of these about 6 months ago and put it in my CR10S4 as I wanted to upgrade it first as it was my first printer. After some messing around, I finally used VSCode and some extensions to flash new firmware to the board as the firmware on the board would not work for my printer. After getting it all said and done, the printing was up and running again and you forget sometimes that it's even running.I just received and installed my second one into my Ender 5 Plus (which is what this board is intended for but can be reflashed with new firmware for other printers), and it was a drop in replacement. I unscrewed the board that was still connected, screwed the new one in, and just moved the connections from the old board to the new board one by one. Doing it this way is a bit tough as some of the wires are the exact length so having the old board still there does get in the way. Fortunately, once I got the wires swapped over, I turned it on, homed the print head, and the motors were also not noticeable.On the side of print quality there is no noticeable difference that I can tell, so you pretty much get this once you get annoyed by the loud noises coming from you printer. Just remember that since its a new board, the settings are reset, so will have to relevel and reset your babysteps if you have them.
Ruesgar
Reseñado en España el 14 de febrero de 2022
No se ha podido cargar el contenido multimedia.
Cliente
Reseñado en España el 2 de septiembre de 2021
Articulo bueno que cumple su función. Vendedor muy bueno, a pesar de estar fuera del plazo de devolución, la placa se estropeo. Al ponerme en contacto con el vendedor en pocos días me llego otra placa completamente nueva sin ningún problema. Todo funciona hasta ahora como debe.
Cliente
Reseñado en España el 25 de abril de 2021
Es impresionantes de como se escuchaban los motores, a cómo han dejado de oírse en los desplazamientos a únicamente oírse los ventiladores. Funciona perfectamente aunque ha costado un poco para reconocerla en Windows 10. Se ha perdido alguna función como 'Pause at Heigh' por ejemplo para el cambio de color de filamento pero se puede solucionar buscando un firmware específico en sitios como GitHub
Productos recomendados